Cooper-instruments-systems Series M3 Digital Force Gage Manual do Utilizador Página 9
- Página / 23
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Series 3 Digital Force Gauges User’s Guide
8
Two filters are available:
Current Reading – Applies to the peak capture rate of the instrument.
Displayed Reading – Applies to the primary reading on the display.
Available settings: 1,2,4,8,16,32,64,128,256,512,1024. It is recommended to keep the current reading
filter at its lowest value for best performance, and the displayed reading filter at its highest value for best
stability.
8 SET POINT INDICATORS
8.1 General Information
Set points are useful for tolerance checking (pass/fail). Two limits, high and low, are specified and stored
in the non-volatile memory of the instrument and the primary reading is compared to these limits.
8.2 Configuration
To configure set points, select Set Points from the menu. The screen will appear as follows:
Either one, two, or none of the set points may be enabled. To toggle between the tension and
compression directions, press the DIRECTION key.
If two set points have been enabled, they are displayed in the upper left corner of the display. If only one
set point has been enabled, the word “OFF” will appear in place of the value. If no set points have been
enabled, the upper left corner of the display will be blank.
When set points are enabled, the following indicators are shown to the left of the primary reading:
– the displayed value is greater than the upper
force limit (NO GO HIGH)
– the displayed value is between the limits (GO)
– the displayed value is less than the lower force
limit (NO GO LOW)
DIGITAL FILTERS
(1 = Fastest)
Current Reading
8
Displayed Reading
1024
SET POINTS
Upper Disabled
* Upper Enabled
5.00
Lower Disabled
* Lower Enabled
3.50
- DIGITAL FORCE GAUGES 1
- Thank you… 2
- TABLE OF CONTENTS 2
- 2 POWER 4
- Caution! 4
- 3 MECHANICAL SETUP 5
- 4 HOME SCREEN AND CONTROLS 6
- 5 OPERATING MODES 8
- 6 CHANGING THE UNITS 8
- 7 DIGITAL FILTERS 8
- 8 SET POINT INDICATORS 9
- 9 COMMUNICATIONS 10
- 10 CALIBRATION 13
- 11 OTHER SETTINGS 17
- 12 SPECIFICATIONS 20
- 23
- 32-1122 23
Manuais e produtos relacionados com Instrumentos de medida Cooper-instruments-systems Series M3 Digital Force Gage
Instrumentos de medida Cooper-instruments-systems M5-1000 High Capacity Digital Force Gage Manual do Utilizador
(28 páginas)
(28 páginas)
Instrumentos de medida Cooper-instruments-systems Series M7 Professional Digital Force Gauge Manual do Utilizador
(41 páginas)
(41 páginas)
Instrumentos de medida Cooper-instruments-systems TSFM 500 Motorized Force Test Stand Manual do Utilizador
(7 páginas)
(7 páginas)
Instrumentos de medida Cooper-instruments-systems LTL 730 Wireless Tension Link Load Cell Manual do Utilizador
(29 páginas)
(29 páginas)
Instrumentos de medida Cooper-instruments-systems ACX-1 Aircraft Cable Tension Meter Manual do Utilizador
(8 páginas)
(8 páginas)
Instrumentos de medida Cooper-instruments-systems DFR 1250 Two Channel Paperless Recorder Manual do Utilizador
(22 páginas)
(22 páginas)
Instrumentos de medida Cooper-instruments-systems STX-1 Digital Strap Tension Meter Manual do Utilizador
(7 páginas)
(7 páginas)
Instrumentos de medida Cooper-instruments-systems WTM 502 Wire Tension Meter Manual do Utilizador
(15 páginas)
(15 páginas)
LG DLGY1902KE podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Suszarki LG DLGY1902KE.
Dostarczamy 1 pdf podręczników LG DLGY1902KE do pobrania za darmo według typów dokumentów: Arkusz Specyfikacji
Comentários a estes Manuais